[2024] Use Valid Exam NSE6_FSW-7.2 by ValidVCE Books For Free Website
Free NSE 6 Network Security Specialist NSE6_FSW-7.2 Official Cert Guide PDF Download
Fortinet NSE6_FSW-7.2 exam is a computer-based test that consists of 60 multiple-choice questions. NSE6_FSW-7.2 exam duration is 120 minutes, and candidates must score at least 70% to pass. NSE6_FSW-7.2 exam can be taken online or at a Pearson VUE testing center. Fortinet recommends that candidates have at least six months of experience working with FortiSwitch products before attempting the NSE6_FSW-7.2 exam.
NEW QUESTION # 13
Refer to the exhibit.
The profile shown in the exhibit is assigned to a group of managed FortiSwitch ports, and these ports are connected to endpoints which are powered by PoE.
Which configuration action can you perform on the LLDP profile to cause these endpoints to exchange PoE information and negotiate power with the managed FortiSwitch?
- A. Assign a new LLDP profile to handle different LLDP-MED TLVs.
- B. Define an LLDP-MED location ID to use standard protocols for power.
- C. Create new a LLDP-MED application type to define the PoE parameters.
- D. Add power management as part of LLDP-MED TLVs to advertise.
Answer: D
NEW QUESTION # 14
Which is a requirement to enable SNMP v2c on a managed FortiSwitch?
- A. Enable an SNMP v3 to handle traps messages with SNMP hosts.
- B. Create an SNMP user to use for authentication and encryption.
- C. Configure SNMP agent and communities.
- D. Specify an SNMP host to send traps to.
Answer: C
NEW QUESTION # 15
Refer to the diagnostic output:
What makes the use of the sniffer command on the FortiSwitch CLI unreliable on__port__23?
- A. The switch port might be used as a trunk member
- B. Just the port egress payloads are printed on CLI.
- C. Only untagged VLAN traffic can be captured.
- D. The types of packets captured is limited.
Answer: D
NEW QUESTION # 16
Which two types of Layer 3 interfaces can participate in dynamic routing on FortiSwitch? (Choose two.)
- A. Loopback interfaces
- B. Switch virtual interfaces
- C. Detected management interfaces
- D. Physical interfaces
Answer: A,B
NEW QUESTION # 17
What can an administrator do to maintain the existing standalone FortlSwltch configuration while changing the management mode to FortLink?
- A. Use a migration tool based on python script to convert the configuration
- B. Register FortiSwitch to For1ISwitch Cloud to save a copy before managing by Forti-Gate.
- C. Enable the Forti-link setting on FortiSwitch before the authorization process
- D. FortiGate will automatically save the existing FortiSwitch configuration during the Forti-link management process.
Answer: C
NEW QUESTION # 18
Which statement about using MAC, IP, and protocol-based VLANs on FortiSwitch is true?
- A. Endpoints are required to use the same FortiSwitch port to remain members of the VLAN.
- B. It provides benefits that can be obtained when using 802.1X authentication.
- C. FortiSwitch uses only the Ethernet type to assign traffic to VLANs.
- D. lt is a scalable and secure solution in comparison to other Layer 2 security measures.
Answer: B
NEW QUESTION # 19
How is traffic routed on FortiSwitch?
- A. Layer 3 routing can be configured on FortiSwitch, while managed by FortiGate.
- B. FortiSwitch looks up the hardware routing table and then the forwarding information base (FIB).
- C. ASIC hardware routing can only handle dynamic routing, if supported.
- D. Hardware-based routing on FortiSwitch is handled by the CPU.
Answer: B
NEW QUESTION # 20
Refer to the diagnostic output:
Two entries in the exhibit show that the same MAC address has been used in two different VLANs. Which MAC address is shown in the above output?
- A. It is a MAC address of FortiGate in HA configuration.
- B. It is a MAC address of a switch that accepts multiple VLANs.
- C. It is a MAC address of an upstream FortiSwitch.
- D. It is a MAC address of FortiLink interface on FortiGate.
Answer: B
NEW QUESTION # 21
Which two statements about managing a FortiSwitch stack on FortiGate are true? (Choose two.)
- A. Only a hardware-based FortiGate can manage a FortiSwitch stack.
- B. FortiSwitch must be operating in standalone mode before authorization.
- C. The switch controller feature must be enabled on FortiGate.
- D. A FortiLink interface must be enabled on FortiGate.
Answer: C,D
NEW QUESTION # 22
To enhance service in emergency situations, to which LLDP-MED Type-Length-Values does Forti-Switch advertise to IP phones?
- A. Power management
- B. Location
- C. Inventory management
- D. Network policy
Answer: C
NEW QUESTION # 23
Which feature should you enable to reduce the number or unwanted IGMP reports processed by the IGMP querier?
- A. Enable the IGMP flood reports setting on the mRouter port.
- B. Enable IGMP flood unknown multicast traffic on the global setting.
- C. Enable IGMP snooping proxy.
- D. Enable the IGMP flood setting on the static port for all multicast groups.
Answer: C
NEW QUESTION # 24
What type of multimode transceiver can be used to split a 40G port?
- A. QSFP transceiver
- B. SFP transceiver
- C. SFP+ transceiver
- D. QSFP+ transceiver
Answer: D
NEW QUESTION # 25
Exhibit.
What conditions does a FortiSwitch need to have to successfully configure the options shown in the exhibit above? (Choose two.)
- A. The CLI commands are enabling a splitpo rt into four 10Gbps interfaces.
- B. The split port can be assigned to native VLAN
- C. The FortiSwitch model is equipped with a maximum of 54 interfaces.
- D. The port full speed prior the split was 100G SFP+
Answer: A,C
NEW QUESTION # 26
Refer to the exhibit.
Core-1 and Access-1 are managed and authorized by FortiGate-1. which uses port4 as the FortiLink interface. After FortiGate authorizes and manages Core-2. Port1 status becomes STP discarding.
Why is port1 in the discarding state?
- A. Core-1 and Core-2 do not have MCLAG configuration.
- B. Access-1 is the root bridge and can only have one root port.
- C. port1 on Core-2 is discarding only management traffic.
- D. Core-2 has the lowest bridge priority.
Answer: A
NEW QUESTION # 27
Which interfaces on FortiSwitch send out FortiLink discovery frames by default in order to detect a FortiGate with an enabled FortiLink interface?
- A. All ports have auto-discovery enabled by default.
- B. The ports with auto-discovery enabled by default are dependent upon the FortiSwitch model.
- C. The last four switch ports on FortiSwitch have auto-discovery enabled by default.
- D. No ports are enabled by default for auto-discovery. This must be configured under config switch interface.
Answer: A
NEW QUESTION # 28
Which statement about the use of the switch port analyzer (SPAN) packet capture method is true?
- A. SPAN can be configured only on a standalone FortiSwitch.
- B. The monitoring device must be connected to the same switch where the traffic is being mirrored
- C. Mirrored traffic can be sent across multiple switches.
- D. Traffic on the management interface can be mirrored and captured by the monitoring device.
Answer: D
NEW QUESTION # 29
How does FortiGate handle configuration of flow tracking sampling if you export the settings to a managed FortiSwitch stack with sampling mode set to perimeter is true?
- A. FortiGate configures and enables flow sampling on FortiSwitch but does not change existing sampling settings of interfaces.
- B. FortiGate configures FortiSwitch to perform ingress sampling on all switch interfaces, except ICL and ISL interfaces.
- C. FortiGate configures FortiSwitch to perform ingress sampling on all switch interfaces.
- D. FortiGate configures and enables egress sampling on all management interfaces.
Answer: B
NEW QUESTION # 30
Which drop policy mode, if assigned to a congested port, will drop incoming packets until there is no congestion on the egress port?
- A. Strict mode
- B. Weighted round robin mode.
- C. Tail-drop mode
- D. Random early detection mode
Answer: C
NEW QUESTION # 31
Which two rules used by MSTP are similar to rules used by other STP methods? (Choose two.)
- A. MSTP uses alternate path and primary path, similar to regular STP.
- B. MSTP uses root bridge selection, similar to rapid STP
- C. MSTP uses timers for transitioning the ports, similar to regular STP.
- D. MSTP uses port role election, similar to rapid STP on the instances.
Answer: A,B
NEW QUESTION # 32
Which two statements about the FortiLink authorization process are true? (Choose two.)
- A. A FortiLink frame is sent by FortiGate to FortiSwitch to complete the authorization.
- B. FortiLink authorization sets the FortiSwitch management mode to FortiLink.
- C. FortiSwitch requires a reboot to complete the authorization process.
- D. The administrator must manually pre-authorize FortiGate on FortiSwitch by adding the FortiGate serial number.
Answer: A,B
NEW QUESTION # 33
Which statement about 802.1X security profiles using MAC-based authentication mode is true?
- A. FortiSwitch performs faster when using this security mode on the ports.
- B. FortiSwitch allows connectivity to all hosts connected to a port, if one host is authenticated.
- C. FortiSwitch can grant each device a different access level based on the credentials provided
- D. FortiSwitch must communicate with the RADIUS server to authenticate devices
Answer: C
NEW QUESTION # 34
......
In today's increasingly complex network environments, the Fortinet NSE6_FSW-7.2 exam is a valuable credential for network security professionals. By passing NSE6_FSW-7.2 exam, candidates can demonstrate their expertise in FortiSwitch networking and security, which can lead to career advancement and increased earning potential. With the growing demand for network security professionals, the NSE6_FSW-7.2 certification is a valuable asset for those seeking to develop their skills and advance their careers in the field of network security.
Fortinet NSE6_FSW-7.2 Official Cert Guide PDF: https://www.validvce.com/NSE6_FSW-7.2-exam-collection.html
Exam NSE6_FSW-7.2: Fortinet NSE 6 - FortiSwitch 7.2 - ValidVCE: https://drive.google.com/open?id=1Mu8bR9i8-OEmU7YH6BnWotaYEHDFnC8N
