Pass Cisco 300-715 Exam in First Attempt Guaranteed [Jun-2024]
Exam Sure Pass Cisco Certification with 300-715 exam questions
To prepare for the Cisco 300-715 exam, candidates should have a good understanding of the Cisco ISE architecture and deployment models. Candidates should also have a good understanding of the various features and functions of Cisco ISE, including identity management, network access control, and policy enforcement. Candidates can prepare for the exam by studying the Cisco ISE Configuration Guide and the Cisco ISE Administration Guide. Candidates can also take advantage of Cisco's online training courses, such as the Implementing and Configuring Cisco Identity Services Engine (SISE) course.
NEW QUESTION # 60
An organization wants to implement 802.1X and is debating whether to use PEAP-MSCHAPv2 or PEAP-EAP-TLS for authentication. Drag the characteristics on the left to the corresponding protocol on the right.
Answer:
Explanation:
NEW QUESTION # 61
What is the minimum certainty factor when creating a profiler policy?
- A. the maximum number that a device certainty factor must reach to become a member of the profile
- B. the minimum number that a predefined condition provides
- C. the minimum number that a device certainty factor must reach to become a member of the profile
- D. the maximum number that a predefined condition provides
Answer: C
Explanation:
Section: Profiler
Explanation/Reference:
NEW QUESTION # 62
Drag and drop the description from the left onto the protocol on the right that is used to carry out system authentication, authentication, and accounting.
Answer:
Explanation:
Explanation
https://www.mbne.net/tech-notes/aaa-tacacs-radius
NEW QUESTION # 63
An engineer is configuring ISE for network device administration and has devices that support both protocols. What are two benefits of choosing TACACS+ over RADUs for these devices? (Choose two.)
- A. TACACS+ encrypts the entire payload being sent while RADIUS only encrypts the password.
- B. TACACS+ is designed for network access control while RADIUS is designed for role-based access.
- C. TACACS+ uses secure EAP-TLS while RADIUS does not.
- D. TACACS+ is FIPS compliant while RADIUS is not
- E. TACACS+ provides the ability to authorize specific commands while RADIUS does not
Answer: A,E
NEW QUESTION # 64
An engineer is configuring 802.1X and wants it to be transparent from the users' point of view. The implementation should provide open authentication on the switch ports while providing strong levels of security for non-authenticated devices. Which deployment mode should be used to achieve this?
- A. open
- B. closed
- C. high-impact
- D. low-impact
Answer: D
Explanation:
Reference:
https://www.lookingpoint.com/blog/cisco-ise-wired-802.1x-deployment-monitormode#:~:text=Low%20impact%20mode%20works%20similar,DHCP%2C%20PXE%20boot%2C%20etc.
NEW QUESTION # 65
An administrator must block access to BYOD endpoints that were onboarded without a certificate and have been reported as stolen in the Cisco ISE My Devices Portal. Which condition must be used when configuring an authorization policy that sets DenyAccess permission?
- A. Endpoint Identity Group is Blocklist, and the BYOD state is Registered.
- B. Endpoint Identity Group is Blocklist, and the BYOD state is Lost.
- C. Endpoint Identity Group is Blocklist, and the BYOD state is Reinstate.
- D. Endpoint Identify Group is Blocklist, and the BYOD state is Pending.
Answer: A
Explanation:
https://www.cisco.com/c/en/us/td/docs/security/ise/2-6/admin_guide/b_ISE_26_admin_guide/b_ISE_admin_26_byod.html
NEW QUESTION # 66
Refer to the exhibit.
A network engineers configuring the switch to accept downloadable ACLs from a Cisco ISC server Which two commands should be run to complete the configuration? (Choose two)
- A. aaa authorization auth-proxy default group radius
- B. ip device tracking
- C. dot1x system-auth-control
- D. radius server vsa sand authentication
- E. radius-server attribute 8 include-in-access-req
Answer: D,E
NEW QUESTION # 67
Which two Cisco ISE deployment models require two nodes configured with dedicated PAN and MnT personas? (Choose two.)
- A. three PSN nodes
- B. seven PSN nodes with one PxGrid node
- C. five PSN nodes with one PxGrid node
- D. two PSN nodes with one PxGrid node
- E. six PSN nodes
Answer: C,D
NEW QUESTION # 68
An enterprise uses a separate PSN for each of its four remote sites. Recently, a user reported receiving an "EAP-TLS authentication failed" message when moving between remote sites. Which configuration must be applied on Cisco ISE?
- A. Renew the expired certificate on one of the PSN.
- B. Add the device to all PSN nodes in the deployment.
- C. Configure an authorization profile for the end users.
- D. Use a third-party certificate on the network device.
Answer: B
Explanation:
When using separate PSNs for different sites, the network device must be added to all PSN nodes in the deployment, so that the device can communicate with the appropriate PSN based on the location of the user1. If the device is not added to all PSN nodes, the user may encounter an EAP-TLS authentication failure when moving between sites, as the device may not be able to reach the PSN that issued the certificate2. The other options are not relevant for this scenario, as they do not address the issue of PSN communication.
NEW QUESTION # 69
A network engineer is configuring Cisco TrustSec and needs to ensure that the Security Group Tag is being transmitted between two devices Where in the Layer 2 frame should this be verified?
- A. 802.1 AE header
- B. CMD filed
- C. 802.1Q filed
- D. Payload
Answer: B
Explanation:
Explanation
https://www.cisco.com/c/dam/global/en_ca/assets/ciscoconnect/2014/pdfs/policy_defined_segmentation_with_tr (slide 25)
NEW QUESTION # 70
Which Cisco ISE service allows an engineer to check the compliance of endpoints before connecting to the network?
- A. qualys
- B. personas
- C. nexpose
- D. posture
Answer: D
Explanation:
https://www.cisco.com/c/en/us/td/docs/security/ise/2-
1/admin_guide/b_ise_admin_guide_21/b_ise_admin_guide_20_chapter_010110.html Posture is a service in Cisco Identity Services Engine (Cisco ISE) that allows you to check the state, also known as posture, of all the endpoints that are connecting to a network for compliance with corporate security policies. This allows you to control clients to access protected areas of a network.
NEW QUESTION # 71
Refer to the exhibit Which switch configuration change will allow only one voice and one data endpoint on each port?
- A. Multi-auth to single-auth
- B. Multi-auth to multi-domain
- C. Mab to dot1x
- D. Auto to manual
Answer: B
Explanation:
https://community.cisco.com/t5/network-access-control/cisco-ise-multi-auth-or-multi-host/m-p/3750907
NEW QUESTION # 72
An engineer is implementing Cisco ISE and needs to configure 802.1X. The port settings are configured for port-based authentication. Which command should be used to complete this configuration?
- A. aaa authentication dot1x default group radius
- B. authentication port-control auto
- C. dot1x system-auth-control
- D. dot1x pae authenticator
Answer: C
Explanation:
Explanation
https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst4500/12-2/31sg/configuration/guide/conf/dot1x.
NEW QUESTION # 73
Which use case validates a change of authorization?
- A. An authenticated, wired EAP-capable endpoint is discovered
- B. An endpoint that is disconnected from the network is discovered
- C. Endpoints are created through device registration for the guests
- D. An endpoint profiling policy is changed for authorization policy.
Answer: D
Explanation:
Explanation
https://www.cisco.com/c/en/us/td/docs/security/ise/1-2/user_guide/ise_user_guide/ise_prof_pol.html
NEW QUESTION # 74
Which supplicant(s) and server(s) are capable of supporting EAP-CHAINING?
- A. Cisco AnyConnect NAM and Cisco Identity Service Engine
- B. Windows Native Supplicant and Cisco Identity Service Engine
- C. Cisco AnyConnect NAM and Cisco Access Control Server
- D. Cisco Secure Services Client and Cisco Access Control Server
Answer: A
Explanation:
Section: Architecture and Deployment
Explanation/Reference: https://www.cisco.com/c/en/us/support/docs/wireless-mobility/eap-fast/200322-Understanding- EAP-FAST-and-Chaining-imp.html
NEW QUESTION # 75
An engineer is using the low-impact mode for a phased deployment of Cisco ISE and is trying to connect to the network prior to authentication.
Which access will be denied in this deployment?
- A. HTTP
- B. EAP
- C. DHCP
- D. DNS
Answer: A
Explanation:
Section: Policy Enforcement
Explanation/Reference:
NEW QUESTION # 76
What are the three default behaviors of Cisco ISE with respect to authentication, when a user connects to a switch that is configured for 802.1X, MAB, and WebAuth? (Choose three)
- A. Unmatched traffic is dropped because of the Reject/Reject/Drop action that is configured under Options.
- B. Unmatched traffic is allowed on the network.
- C. Dot1X traffic uses a user-defined identity store for retrieving identity.
- D. Dot1x traffic uses internal users for retrieving identity.
- E. MAB traffic uses internal endpoints for retrieving identity.
Answer: A,C,E
NEW QUESTION # 77
An administrator for a small network is configuring Cisco ISE to provide dynamic network access to users. Management needs Cisco ISE to not automatically trigger a CoA whenever a profile change is detected. Instead, the administrator needs to verify the new profile and manually trigger a CoA.
What must be configuring in the profiler to accomplish this goal?
- A. Session Query
- B. Reauth
- C. No CoA
- D. Port Bounce
Answer: C
Explanation:
Reference:
https://ciscocustomer.lookbookhq.com/iseguidedjourney/ISE-profiling-policies
NEW QUESTION # 78
An administrator is configuring posture with Cisco ISE and wants to check that specific services are present on the workstations that are attempting to access the network. What must be configured to accomplish this goal?
- A. Create a registry posture condition using a non-OPSWAT API version.
- B. Create a compound posture condition using a OPSWAT API version.
- C. Create a service posture condition using a non-OPSWAT API version.
- D. Create an application posture condition using a OPSWAT API version.
Answer: C
NEW QUESTION # 79
Which interface-level command is needed to turn on 802 1X authentication?
- A. Dofl1x pae authenticator
- B. authentication host-mode single-host
- C. aaa server radius dynamic-author
- D. dot1x system-auth-control
Answer: B
NEW QUESTION # 80
A customer wants to set up the Sponsor portal and delegate the authentication flow to a third party for added security while using Kerberos Which database should be used to accomplish this goal?
- A. Active Directory
- B. LDAP
- C. RSA Token Server
- D. Local Database
Answer: A
Explanation:
Explanation
https://www.cisco.com/c/en/us/td/docs/security/ise/2-6/admin_guide/b_ise_admin_guide_26/b_ise_admin_guide
NEW QUESTION # 81
The IT manager wants to provide different levels of access to network devices when users authenticate using TACACS+. The company needs specific commands to be allowed based on the Active Directory group membership of the different roles within the IT department. The solution must minimize the number of objects created in Cisco ISE. What must be created to accomplish this task?
- A. one shell profile and one command set
- B. one shell profile and multiple command sets
- C. multiple shell profiles and multiple command sets
- D. multiple shell profiles and one command set
Answer: B
NEW QUESTION # 82
......
Real Cisco 300-715 Exam Questions Study Guide: https://www.validvce.com/300-715-exam-collection.html
Download Real 300-715 Exam Dumps for candidates. 100% Free Dump Files: https://drive.google.com/open?id=11Z8Lb6P8wxjfXzm7ziW1OKp6NE-HxZep
