Updated Free NACE NACE-CIP2-001 Test Engine Questions with 100 Q&As
The Best CIP Level 2 NACE-CIP2-001 Professional Exam Questions
NEW QUESTION 28
Corrosion is the reverse process of
- A. galvanic deterioration.
- B. flaking.
- C. hot dipping.
- D. steel manufacturing.
Answer: D
NEW QUESTION 29
You are the NACE Coating Inspector on a tank lining project and are asked to perform a high voltage holiday test after the coating applicators have completed their final repairs. After meeting all the confined space entry permit you enter the tank and notice a very strong odor of solvent.
Your first course of action should to:
- A. Exit the tank and document the incident in your daily report
- B. Don your air supplied respirator and continue the testing
- C. Investigate to find the source of the odor
- D. Exit the tank and immediately and report the problem to the nearest safety supervisor
Answer: D
NEW QUESTION 30
In powder coatings, when the particles of powder begin to flow but are not fully liquid, they are in what stage?
- A. Flow stage
- B. Gel stage
- C. Wetting stage
- D. Cure stage
Answer: A
NEW QUESTION 31
When conducting inspections the Inspector should follow which standards:
- A. NACE and SSPC standards in North America
- B. Australian standards in Australia
- C. The specified standards
- D. ISO standards in Europe and Asia
Answer: C
NEW QUESTION 32
Which type of pipelines collect the gas from the transmission system so utility companies can distribute the gas to end users?
- A. Gathering
- B. Transmission
- C. Midstream
- D. Distribution
Answer: D
NEW QUESTION 33
The coating applicator has ignored a enface preparation hold point and applied coating over the surface without a sign off from you as the inspector.
Your FIRST preferred course of action is to:
- A. Stop the job
- B. Ignore the situation
- C. Advise the Owner and write a Non-Conformance report
- D. Require the Applicator to remove the coating
Answer: D
NEW QUESTION 34
When environmental enclosures are being used an inspector needs to be concerned about:
- A. Lighting
- B. a), b), and c)
- C. Air changes
- D. Structural integrity
Answer: B
NEW QUESTION 35
Coating Surveys are legally required:
- A. On high pressure gas lines and fireproofed structures
- B. On water tanks and potable water pipelines
- C. On commercial marine vessels and offshore platforms
- D. On food and beverage vessels and can linings
Answer: C
NEW QUESTION 36
The Inspectors' goal at the Pre-Job Conference is to:
- A. Obtain a clear understanding of the Specification
- B. Take accurate meeting minutes for distribution
- C. Manage the meeting so it doesn't go off topic
- D. Discuss contractual requirements
Answer: A
NEW QUESTION 37
In the event of a conflict between the Product Data Sheet and the Specification:
- A. It is up to the Applicator to decide which one to follow
- B. The Product Data Sheet prevails
- C. It is up to the Inspector to decide which one to follow
- D. The Specification prevails
Answer: D
NEW QUESTION 38
When performing testing in accordance with ASTM D 2583 the inspector may observe:
- A. Cold flow or creep
- B. Adhesion failure
- C. Cohesion failure
- D. Glue failure
Answer: A
NEW QUESTION 39
You are the NACE Level 2 Inspector with the final responsibility to prepare the final report for a very large structural steel shop project which has gone very well. It is due next week. The work has been ongoing for two years and several NACE Level 1 Inspectors have worked under your supervision throughout the project. You find you are missing one week of daily reports for the night shift from the very beginning of the project and despite your best efforts they are cannot found.
You FIRST preferred course of action is to:
- A. Re-create the reports as not much was going on during night shift anyway
- B. Plainly state in your report that they are missing
- C. Use creative writing to cover over the fact they are missing
- D. Do not complete your report until they can be found
Answer: B
NEW QUESTION 40
NACE Level 2 Inspectors have been authorized to perform:
- A. Visual inspection, Non-Destructive and Destructive testing
- B. Visual inspection only
- C. All types of inspection without supervision
- D. Visual inspection and Non-destructive testing
Answer: A
NEW QUESTION 41
The number of air turns in an enclosure can be affected by all of these EXCEPT
- A. manufacturer of the equipment.
- B. time of the year (winter/summer).
- C. type of dehumidification equipment (refrigerant or desiccant).
- D. coating type.
Answer: D
NEW QUESTION 42
From a corrosion perspective, the main difference between Ferrous and Non-Ferrous Metals is:
- A. Cost
- B. Safety
- C. Appearance
- D. Iron content
Answer: D
NEW QUESTION 43
Inspectors perform tests on linings that they may not perform on exterior coatings because
- A. linings protect the contents and the container.
- B. linings are more durable than coatings.
- C. coatings are expected to degrade over time.
- D. coatings are more durable than linings.
Answer: A
NEW QUESTION 44
You are working as an inspector in a galvanizing plant for the first time.
What are some of the hazards you need to be aware of:
- A. Risk of skin
- B. a), b), and c)
- C. Risk of chemical exposure
- D. Risk of acid or caustic splashes
Answer: B
NEW QUESTION 45
You can use magnifiers to examine all of the following EXCEPT
- A. Blisters
- B. Surface cleanliness
- C. Mill scale
- D. Surface profile
Answer: B
NEW QUESTION 46
NACE/SSPC Water Jetting standards are directly equivalent to ISO Abrasive Blast Standards:
- A. True
- B. False
Answer: B
NEW QUESTION 47
Measuring methyl ethyl ketone (MEK) resistance of ethyl silicate inorganic zinc-rich primers by solvent rub requires
- A. 25 double rubs with a saturated cloth.
- B. 35 single rubs with a saturated cloth.
- C. 25 single rubs with a saturated cloth.
- D. 50 double rubs with a saturated cloth.
Answer: D
NEW QUESTION 48
When performing an adhesion test in accordance with ASTM D 3359 where the Dry Film Thickness is approximately 10 mils, the Inspector should use:
- A. Method B - Cross Hatch
- B. Method A - Cross Hatch
- C. Method A - X Cut
- D. Method B - X cut
Answer: C
NEW QUESTION 49
Because a NACE Level 2 Inspector has been trained in specific destructive tests, it is up to the Inspector to decide if and when a destructive test is required.
- A. True
- B. False
Answer: B
NEW QUESTION 50
Thermal Spray coatings provide:
- A. Barrier protection
- B. Inhibitive protection
- C. Sacrificial protection
- D. Thermal protection
Answer: C
NEW QUESTION 51
......
Try 100% Updated NACE-CIP2-001 Exam Questions [2022]: https://www.validvce.com/NACE-CIP2-001-exam-collection.html
Pass NACE-CIP2-001 Exam - Real Questions & Answers: https://drive.google.com/open?id=1ab-dKpkrVb9Hnnja--QZFW-qFEcnzp5w
